Відео

Rotary products are sold through distribution. To find the your nearest Rotary Distributor please visit our website. rotarylift.com/contact-distributor/

You will need to raise the lift so that it is off of the locks. Then follow the instructions in this video to adjust the latch locks. Once adjusted you should be able to pull down on the lock release and the latch locks should disengage.

Lock release cable adjustment should be done while the lift is NOT on the locks. It doesn't really matter if the lift is up in the air or down on the ground.

Yes you can equipment your standard lift with Shockwave, but it would require replacing the power unit and both hydraulic cylinders.

When you press the blue button it should ask “Are you Sure?” with green and red yes/no options. This puts the system in Quick Check Mode. To get out of QCM press the Red Arrow Back Button until the box at the bottom of the screen is no longer outlined in blue.

Great question...The alignment system is mobile, meaning that there is no bulky tower so you do not need a dedicated bay. This true 3d system allows you to check a vehicle's alignment in any bay.

@rotarylift with out a lift thinking of getting one for my home garage

While this system can do alignment checks without a lift, it is recommended that alignment adjustments are done on an alignment lift.

I requed my inground rotary lift from an old service station, ..roof collapsed on it..not for scraping..but to put back in service..tested it with a portable gas compressor..to see if it would raise up..? Shure did!.. held air model FP 46 H .full hydraulic pump out oil , when they were tearing down the place I gave them 300 bucks to careful remove it. Put it on my trailer. Next is history.. fully restored.. piping control valves ..seal .. sandblasted casing.paint lastly truck bed liner rolled on. Oil tank now above ground..back in service for another 50 yrs ..

The Rotary R1065 comes setup with the USA database, but the European database can be turned on also.

Good question. The answer is yes, our R3AC80 and R3AC60 models are compatible with electric vehicles.

Rotary products are sold through distribution. To find the your nearest Rotary Distributor please visit our website. rotarylift.com/contact-distributor/

Rotary products are sold through distribution. To find the your nearest Rotary Distributor please visit our website. rotarylift.com/contact-distributor/

Yes you can. The specs for this changer are - External Clamping 10" to 26", Internal Clamping 12" to 28", Max Tire Width 15", and Max Tire Diameter is 45".

@@RotarySolutions thanks you for answers

Rotary products are sold through distribution. To find the your nearest Rotary Distributor please visit our website. rotarylift.com/contact-distributor/

The side that clicks last/later is generally found to be too loose. That side will need to be tightened up to match the 1st clicking side. *note, only adjust cables only while unloaded

The side that clicks last/later is generally found to be too loose. That side will need to be tightened up to match the 1st clicking side. *note, only adjust cables only while unloaded

So, If the RIGHT (Power ) side clicks FIRST, do I tighten the RIGHT cable or LEFT cable? (IE Left adjust nut adjusts Right side and vice versa, I THINK). Thank you, Michael @@RotarySolutions

The side that clicks last would need to be tightened. So, if the right (Power unit) side clicks last then you will need to tighten the right side to match the left side.

WHICH adjusting NUT controls WHICH SIDE? In other words, does right nut tighten left side or right side. @@RotarySolutions

The nut on the right side controls the right side, this is the same with the left side. So, if the right (Power unit) side clicks last then you will need to tighten the right side to match the clicking on the left side.

Yes it will work on a 218" wheelbase.

Thank you very much!

Sounds like your lock release latch is stuck. Here's a video on how to adjust it. ua-cam.com/video/pLy1oj-7Oec/v-deo.html

Yes, lifted runout compensation is possible with the R1065.

Rotary products are sold through distribution. To find the your nearest Rotary Distributor please visit our website. rotarylift.com/contact-distributor/

Rotary products are sold through distribution. To find the your nearest Rotary Distributor please visit our website. rotarylift.com/contact-distributor/

We have a video showing how to fill and bleed your 2-post lift. ua-cam.com/video/kTEofKfcGVg/v-deo.html

@@RotarySolutions Thank you.

Sounds like the lift needs a slight cable adjustment. We recommend contacting your closest RAI to get the issue fixed and to get the lift inspected. rotarylift.com/contact-distributor/

Yeah, I get that a lot. You'll really have to hear it if it's really synced with each other the slightest offset will do that ... Once you catch it you'll know to adjust it a tad bit... If not back out the nut on both and start over

We recommend that toe be adjusted with the vehicle resting at ride height.